logo

How to Specify Integrated Sewage Treatment Equipment: Five Parameters That Decide the Design and the Price

November 16, 2026
Latest company blog about How to Specify Integrated Sewage Treatment Equipment: Five Parameters That Decide the Design and the Price

At the inquiry stage, most buyers provide exactly one number: daily flow. Yet two integrated sewage treatment equipment packages both rated at 50 m³/day can differ in price by more than double. The gap rarely comes from materials or brand — it comes from four parameters left unstated: influent quality, effluent destination, site conditions and operating capability.

Together they determine the process train, tank ratios, equipment configuration and degree of automation, and therefore the price.

How to Specify Integrated Sewage Treatment Equipment: Five Parameters That Decide the Design and the Price

1. Flow rate: look beyond the daily average

Daily flow is the starting point, not the whole picture. Domestic wastewater peaks in the morning, midday and evening, with hourly peaking factors typically between 1.5 and 2.5. Resorts and tourist sites show pronounced high and low seasons. Livestock and aquaculture operations swing with stocking and harvest cycles, where the peak-to-trough ratio can reach three to one.

Size a system on the daily average alone and the hydraulic retention time collapses during peaks, producing periodic effluent violations.

The engineering response is straightforward: set biological tank volume on the daily average, check piping, pumps and disinfection against peak flow, and provide equalization of at least six to eight hours of average flow. Where flow varies sharply, increase equalization to twelve hours or more, and state the peaking factor the design assumes in the contract.

2. Influent quality: this decides the process train, not the equipment size

"Hospital wastewater" carries disinfection by-products and pharmaceutical residues, requiring stronger disinfection and longer contact time. Restaurant effluent is high in fats and oils, calling for grease separation and dissolved air flotation. Aquaculture discharge has high ammonia and nitrite with an imbalanced carbon-to-nitrogen ratio, requiring carbon dosing or enhanced denitrification.

Food processing effluent can reach several thousand mg/L COD and needs pretreatment before any biological stage. Salinity matters as much: chloride intrusion in coastal areas, or seawater-based aquaculture, inhibits microbial activity and accelerates carbon steel corrosion.

The usual test for biodegradability is the BOD5 to COD ratio. Above 0.3, biological treatment fits. Between 0.2 and 0.3, add hydrolytic acidification as pretreatment. Below 0.2, evaluate physical-chemical or advanced oxidation routes. A complete influent analysis at inquiry stage is worth more than a week of revised quotations.

How to Specify Integrated Sewage Treatment Equipment: Five Parameters That Decide the Design and the Price

3. Effluent standard and destination: discharge and reuse are two different packages

Discharge to a municipal sewer, discharge to a surface water body, and reuse for irrigation or process water imply materially different standards and configurations. Sewer discharge usually needs only pretreatment and conventional biological treatment. Discharge to sensitive water bodies often requires Class 1A limits or stricter, with polishing and disinfection.

Reuse brings membrane filtration or MBR into scope, along with turbidity, colour and microbiological targets.

One caution: the tighter the standard, the faster operating cost rises. Where local enforcement capacity is limited and operators are scarce, a "moderate configuration with low operating demand" is often more reliable than a maximum-specification system that nobody can run.

4. Site conditions: buried or above ground determines structural design and access

Integrated sewage treatment equipment can be buried, installed above ground, or placed on a roof or plant room floor. Buried installation must account for soil cover loads, groundwater level and uplift resistance, which means a reinforced structure. Above-ground installation is easier to service but consumes land and affects visual impact; cold regions also require insulation and freeze protection.

Transport corridor width, lifting radius and power supply specification — single or three phase, voltage and frequency — all shape the delivery method and cost.

Overseas projects should confirm container unloading conditions and on-site crane capacity early. A complete 40-foot unit typically weighs 8 to 15 tonnes; where no crane is available, the split-shipment plan must be agreed at contract stage.

5. Operating capability: this sets the automation level and spares strategy

The same equipment, run by a trained team versus a part-time operator, can differ in service life by several years. Where operating resources are thin, prioritise simple control logic, clear alarms and remote monitoring, and require multilingual manuals, a wear-parts list and video guidance. Where the owner has in-house technicians, automation can be trimmed to reduce capital cost.

Parameter Typical range Effect on design and price
Daily flow 5–200 m³/day Sets tank volume, membrane area and unit size
Hourly peaking factor 1.5–2.5 Sets equalization volume and margin on pumps and disinfection
Influent COD 200–600 mg/L (domestic) Sets biological retention time and aeration demand
Effluent standard Sewer / Class 1A / reuse Determines membrane, polishing and disinfection scope
Installation mode Buried / above ground / indoor Determines structural strength, insulation and service access
Six documents to send with your inquiry
  1. Average and peak daily flow, with notes on seasonal variation.
  2. Influent analysis covering at least COD, BOD5, SS, ammonia nitrogen, pH, oils and salinity.
  3. Effluent standard and discharge destination; reuse projects should attach reuse quality targets.
  4. Site plan, groundwater level, soil cover depth and lifting conditions.
  5. Power supply specification, local voltage and frequency, and any explosion-proof requirement.
  6. Operator staffing and required documentation language.

State these six items clearly and a supplier can return a comparable proposal within two weeks, instead of probing with three different quotations. Specifying integrated sewage treatment equipment is really about moving engineering judgement forward to the inquiry stage: two extra days spent confirming parameters can save two months of commissioning disputes.

How to Specify Integrated Sewage Treatment Equipment: Five Parameters That Decide the Design and the Price